Audi A4

since 1994 release

Repair and operation of the car



A4 Audi
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ System of an exhaust
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and channels of absorption
+ System of injection
+ Coupling
+ Transmission and main transfer
+ Suspension bracket of wheels and steering
+ Brakes
+ Wheels and tires
+ Electrotechnical equipment
+ System of ignition
+ Lighting
+ Alarm equipment
+ Tools and devices
+ Heating and ventilation
+ body Details
- Salon
   Control panel
   Average console
   Seats
Search of malfunctions
Technical characteristics





Seats

Dismantle of forward seats

Dismantle of forward seats (model with the lock screw): weaken ahead on a seat the lock screw (1) and disconnect the shtekerny socket (2) – here heating of a seat.


Dismantle of forward seats: unscrew a stopper (1), wring out a decorative cap (2) and remove the decorative panel (3).


 PERFORMANCE ORDER

  1. Wring out decorative caps of the panel behind on the internal tire of a seat, weaken the screw, remove the panel back.
  2. Unscrew on the external tire of a seat the screw with a crosswise head and remove a stopper.
  3. Disconnect sockets of wires of heating of a seat and the electric drive of adjustment.
  4. Seats with manual adjustment: unscrew on the average tire of a seat ahead the lock screw.
  5. The buffer spring is installed in some cars instead of the lock screw.
  6. Seats with the adjustment electric drive, heating of seats: wring out ahead on the right and at the left on the tire of seats of a covering and unscrew under them screws.
  7. Ahead lift a seat, open collars of wires, disconnect sockets.
  8. For all: remove a seat back.
  9. Before installation check, whether so-called rams outside on seat support, and also ahead in the middle are damaged. Otherwise the seat will shake.

Dismantle of head restraints

 PERFORMANCE ORDER

  1. In sockets which the fixing core of a head restraint enters, it is integrated on one key.
  2. Press a key.
  3. Remove head restraints up.

Dismantle of a back seat

Lateral facing which is outside near the leaning-back back of a back seat, is screwed in the middle of (2). Above (1) and below (3) it is only hung.

Dismantle of a pillow of a seat

 PERFORMANCE ORDER

  1. Lift a seat pillow.
  2. At installation track that thorns on the lower party of a pillow of a seat entered reception openings under the seat console.
  3. Dismantle of separate backs: cast away the corresponding back.
  4. Unscrew the average hinge and remove part of a back.
  5. Weaken under it the screw with a crosswise head.
  6. Take out part of a back from the average hinge and pull to the middle from directing on a sidewall.
  7. Dismantle of lateral facing near the cast-away seat back: cast away a seat back.
  8. Weaken from the inside screw connection approximately on the middle of height of lateral facing.
  9. Shift lateral facing up and take out from clips.
  10. Dismantle of a rigid back: dismantle a seat pillow.
  11. Dismantle head restraints.
  12. Carefully take out directing head restraints from a back of a back seat up.
  13. Weaken two screw connections at bottom edge of a back.
  14. Shift a back up and take out from clips.

Dismantle of a back reception pocket

 PERFORMANCE ORDER

  1. Cast away a back of a back seat and dismantle lateral facing or a rigid back.
  2. Lift a back reception pocket for a first line and pull forward, thus clamps will leave grooves at back edge.
  3. If to pull a reception pocket a little forward, it is possible to unscrew the automatic device of a seat belt. For dismantle of loudspeakers it is enough to pull only a reception pocket forward.

Seat belts

On forward seats in Audi there is a pyrotechnic device of a tension of a seat belt. Just as in a safety cushion, at operation the small charge of explosive which tightens belts to the driver and to the passenger near the driver is lit. Just as in case of a safety cushion (the head Podvesk of wheels and a steering), the strict safety rules concerning installation and dismantle work for the device of a tension of a seat belt. Dismantle and installation – work for a workshop.










.
, .